6.5 Inch (6½") Black Plastic Speaker Adapter Bracket Ring Select Models Compatible with Nissan / Infiniti

The front door speakers in my 2002 Nissan Xterra (built in 2001) were factory molded to extend out from the door a couple inches. On some earlier Xterras and Frontiers, this extension - or "spacer ring" - was separate from the speaker and could be reused with after-market 6.5-inch speakers. My setup had the spacer ring and speaker as one piece. Naively, I had given away those stock speakers before realizing I needed the extra space and adapter; some DIYers had cut out the speaker and reused the ring. This Adapter Bracket Ring worked perfectly for my vehicle. It allows the speakers to be mounted out from the door so that 1) the magnets do not interfere with - or sit close to - the door glass when rolled down; and 2) the speakers sit closer to the door panel's speaker grill allowing for better sound projection. Note that the top surface of the adapter/spacer ring is solid. This requires an extra step or two with install but accommodates variances in mounting screw locations of the after-market speaker. Overall, this is much better than the flat adapter rings commonly found at most electronics retailers.

I purchased these Black, Plastic Speaker Adapter Ring Brackets to use Skar Audio - RPX65 6 1/2" 2-Way 4-Ohm Speakers in the front doors of my 2004 Nissan - Sentra 1.8S Car. I used speaker gasket tape & sealed the speaker to the mounting rings for a good seal. The speakers lined right up & so did the three holes on the adapter rings brackets for a perfect fit. These are very good quality unlike other brands sold here on Amazon & are well worth the low cost. I am happy with my purchase & I recommend this product to anyone with a 2004 Nissan - Sentra 1.8S Car.

Good product well made, perfect fit with old stock adapter on nissan frontier 2002. Most amazon products don’t provide dimensions wherelse competitors provide more info with mm calculation

Very simple light plastic spacer and adapter for most nissan front door speakers that use 6.5” speakers and mounted with 3 screws to door panel. The adapter looks like you can use 5.25” spkrs too with smaller holes on the inside of the adapter as well as on the ring for 6.5” spkrs. Its not going to give large depth speakers enough room to clear windows so get slim speakers for the door. Otherwise simple to screw on new speakers as small pilot holes are there already. Works well for my 350z.

2016 Nissan Versa SV - Did not fit perfectly, two holes aligned. I had to drill one just below the third one for it to fit. No big deal, used a 7/32 drill bit and the bolt fit perfectly. On the back side of the bracket, below the hole, there is a an circle outline. This coincidentally aligned perfectly with the one on the door. Seeing as there not many brackets out there yet that seem to fit my car perfectly, this did the job great with slight modification. Glad I took the chance since my car was not on the list as being compatible.

Perfect for my 2016 Juke and JL Audio 6.5" speakers. Even those these are not entirely solid, they are quite sturdy. I've looked everywhere for something possibly better, and that would require a combination of a few different adapters and rings bonded together for 3x the cost of these. That or something entirely DIY and cut with costly equipment. These will do just fine.There's also cheaper quality out there. This is the best bang for the buck. There's 4 pre-existing holes on the top to mount the speakers. Good chance your speakers will line up somehow, but I assume it would be easy enough to drill new holes if need be. I added some parts express speaker gasket to ensure a good seal on both the speaker and the door.

2014 Nissan Versa fit like a charm. I like how the pre-drilled holes on the outer edge and with-in are included so that mainly any style of 6.5 can be mounted and then placed in the panel. The skarrpx65 have a deep basket that had to be mounted “on” the adapter rather “in”. The 3 holes aligned perfectly with the 3 existing holes to mount into my door and keep moving with my life. Great product!! Great price.

One of the people asked if they fit Nissan sentra. Answer was 2000-2008 I think. I have a 2005 and these did not line up with the factory bolt holes. Didn't feel like taking my does apart again so just used them with self tapping screws. Not my preference but whatever! So NO THEY DO NOT FIT 2005 Sentra and yes I rotated the three bolt pattern all around and still no lineup.